Follow these guidelines for safe towing:
  • Do not tow a trailer until you drive your vehicle at least 1000 mi (1,600 km).
  • Consult your local motor vehicle laws for towing a trailer.
  • See the instructions included with towing accessories for the proper installation and adjustment specifications.
  • Service your vehicle more frequently if you tow a trailer.  See   Scheduled Maintenance
  • If you use a rental trailer, follow the instructions the rental agency gives you.
Another chapter of this manual contains load specification terms found on the tire label and Safety Compliance label and instructions on calculating your vehicle's load.   See   Load Limit
Remember to account for the trailer tongue weight as part of your vehicle load when calculating the total vehicle weight.
Hitches
Do not use a hitch that either clamps onto the bumper or attaches to the axle.
Distribute the trailer load so 10-15% of the total trailer weight is on the tongue.
Weight-Distributing Hitches
  WARNING:  Do not adjust the spring bars so that your vehicle's rear bumper is higher than before attaching the trailer. Doing so will defeat the function of the weight-distributing hitch, which may cause unpredictable handling, and could result in serious personal injury.

When hooking-up a trailer using a weight-distributing hitch, always use the following procedure:
  1. Park the loaded vehicle, without the trailer, on a level surface.
  1. Measure the height to the top of your vehicle’s front wheel opening on the fender. This is H1.
  1. Securely attach the loaded trailer to your vehicle without the weight-distributing bars connected.
  1. Measure the height to the top of your vehicle’s front wheel opening on the fender a second time. This is H2.
  1. Install and adjust the tension in the weight-distributing bars so that the height of your vehicle’s front wheel opening on the fender is approximately halfway between H1 and H2.
  1. Check that the trailer is level or slightly nose down toward your vehicle. If not, adjust the ball height accordingly and repeat Steps 1-6.
  1. Lock the bar tension adjuster in place.
  1. Check that the trailer tongue securely attaches and locks onto the hitch.
  1. Install safety chains, lighting and trailer brake controls as required by law or the trailer manufacturer.
Safety Chains
Note:   Never attach safety chains to the bumper.
Always connect the safety chains to the hook retainers of your vehicle hitch.
To connect the safety chains, cross them under the trailer tongue and allow enough slack for turning tight corners. Do not allow the chains to drag on the ground.
Trailer Brakes
  WARNING:  Do not connect a trailer's hydraulic brake system directly to your vehicle's brake system. Your vehicle may not have enough braking power and your chances of having a collision greatly increase.

Electric brakes and manual, automatic or surge-type trailer brakes are safe if you install them properly and adjust them to the manufacturer's specifications. The trailer brakes must meet local and federal regulations.
The rating for the tow vehicle's braking system operation is at the gross vehicle weight rating, not the gross combined weight rating.
Separate functioning brake systems are required for safe control of towed vehicles and trailers weighing more than 1500 lb (680 kg) when loaded.
Trailer Lamps
  WARNING:  Never connect any trailer lamp wiring to the vehicle's tail lamp wiring; this may damage the electrical system resulting in fire. Contact your authorized dealer as soon as possible for assistance in proper trailer tow wiring installation. Additional electrical equipment may be required.

Trailer lamps are required on most towed vehicles. Make sure all running lights, brake lights, direction indicators and hazard lights are working.
Before Towing a Trailer
Practice turning, stopping and backing up to get the feel of your vehicle-trailer combination before starting on a trip. When turning, make wider turns so the trailer wheels clear curbs and other obstacles.
When Towing a Trailer
  • Do not drive faster than 70 mph (113 km/h) during the first 500 mi (800 km).
  • Do not make full-throttle starts.
  • Check your hitch, electrical connections and trailer wheel lug nuts thoroughly after you have traveled 50 mi (80 km).
  • When stopped in congested or heavy traffic during hot weather, place the gearshift in park (P) to aid engine and transmission cooling and to help air conditioning performance.
  • Switch off the speed control with heavy loads or in hilly terrain. The speed control may turn off automatically when you are towing on long, steep grades.
  • Shift to a lower gear when driving down a long or steep hill. Do not apply the brakes continuously, as they may overheat and become less effective.
  • If your transmission is equipped with a Grade Assist or Tow/Haul feature, use this feature when towing. This provides engine braking and helps eliminate excessive transmission shifting for optimum fuel economy and transmission cooling.
  • Allow more distance for stopping with a trailer attached. Anticipate stops and brake gradually.
  • Avoid parking on a grade. However, if you must park on a grade:
  1. Turn the steering wheel to point your vehicle tires away from traffic flow.
  1. Set your vehicle parking brake.
  1. Place the automatic transmission in park (P).
  1. Place wheel chocks in the front and back of the trailer wheels. (Chocks not included with vehicle.)
Launching or Retrieving a Boat or Personal Watercraft (PWC)
Note:   Disconnect the wiring to the trailer before backing the trailer into the water.
Note:   Reconnect the wiring to the trailer after removing the trailer from the water.
When backing down a ramp during boat launching or retrieval:
  • Do not allow the static water level to rise above the bottom edge of the rear bumper.
  • Do not allow waves to break higher than 6 in (15 cm) above the bottom edge of the rear bumper.
Exceeding these limits may allow water to enter vehicle components:
  • Causing internal damage to the components.
  • Affecting driveability, emissions and reliability.
Replace the rear axle lubricant anytime the rear axle has been submerged in water. Water may have contaminated the rear axle lubricant, which is not normally checked or changed unless a leak is suspected or other axle repair is required.