WARNING:
You are responsible for controlling your vehicle at all times. The system is designed to be an aid and does not relieve you of your responsibility to drive with due care and attention. Failure to follow this instruction could result in the loss of control of your vehicle, personal injury or death.
WARNING:
The system does not detect vehicles that are driving in a different direction, pedestrians at night, cyclists or animals. Failure to take care may result in the loss of control of your vehicle, serious personal injury or death.
WARNING:
The system does not operate during hard acceleration or steering. Failure to take care may lead to a crash or personal injury.
WARNING:
The system may fail or operate with reduced function during cold and severe weather conditions. Snow, ice, rain, spray and fog can adversely affect the system. Keep the front camera and radar free of snow and ice. Failure to take care may result in the loss of control of your vehicle, serious personal injury or death.
WARNING:
In situations where the vehicle camera has limited detection capability, this may reduce system performance. These situations include but are not limited to direct or low sunlight, vehicles at night without tail lights, unconventional vehicle types, pedestrians with complex backgrounds, running pedestrians, partly obscured pedestrians, or pedestrians that the system cannot distinguish from a group. Failure to take care may result in the loss of control of your vehicle, serious personal injury or death.
WARNING:
The system cannot help prevent all crashes. Do not rely on this system to replace driver judgment and the need to maintain a safe distance and speed. |
Using the Pre-Collision Assist System
The system is active at speeds above approximately
3 mph (5 km/h) and pedestrian detection is active at speeds up to
50 mph (80 km/h).
If your vehicle is rapidly approaching another stationary vehicle, a vehicle traveling in the same direction as yours, or a pedestrian within your driving path, the system is designed to provide three levels of functionality:
- Alert
- Brake Support
- Active Braking
Alert: When activated, a flashing visual warning displays and an audible warning chime sounds.
Brake Support: Assists the driver in reducing collision speed by preparing the brake system for rapid braking. Brake support does not automatically activate the brakes, but if the brake pedal is pressed even lightly by the driver, brake support could add additional braking up to full force.
Active Braking: Active braking may activate if the system determines that a collision is imminent. The system may help the driver reduce impact damage or avoid the crash completely.
Note:
If you perceive Pre-Collision Assist alerts as being too frequent or disturbing, then you can reduce the alert sensitivity, though the manufacturer recommends using the highest sensitivity setting where possible. Setting lower sensitivity would lead to fewer and later system warnings.
Adjusting the Pre-Collision Assist Settings
You can adjust the alert sensitivity to one of three possible settings by using the information display control. See
General Information.
If required, you can switch active braking off using the information display control. See
General Information.
Note:
Active braking automatically turns on every time you switch the ignition on.
Blocked Sensors
If a message regarding a blocked sensor or camera appears in the information display, the radar signals or camera images are obstructed. The radar sensor is located behind a fascia cover near the driver side of the lower grille. With an obstructed radar, the Pre-Collision Assist system does not function and cannot detect a vehicle ahead. With the front camera obstructed, the Pre-Collision Assist system does not respond to pedestrians or stationary vehicles and the system performance on moving vehicles reduces. The following table lists possible causes and actions for when this message displays.
Cause
| Action
|
---|
The surface of the radar in the grille is dirty or obstructed in some way.
| Clean the grille surface in front of the radar or remove the object causing the obstruction.
|
The surface of the radar in the grille is clean but the message remains in the display.
| Wait a short time. It may take several minutes for the radar to detect that there is no obstruction.
|
Heavy rain, spray, snow, or fog is interfering with the radar signals.
| The Pre-Collision Assist system is temporarily disabled. Pre-Collision Assist should automatically reactivate a short time after the weather conditions improve.
|
Swirling water, or snow or ice on the surface of the road may interfere with the radar signals.
| The Pre-Collision Assist system is temporarily disabled. Pre-Collision Assist should automatically reactivate a short time after the weather conditions improve.
|
Radar is out of alignment due to a front end impact.
| Contact an authorized dealer to have the radar checked for proper coverage and operation.
|
The windshield in front of the camera is dirty or obstructed in some way.
| Clean the outside of the windshield in front of the camera.
|
The windshield in front of the camera is clean but the message remains in the display.
| Wait a short time. It may take several minutes for the camera to detect that there is no obstruction.
|
Note:
Proper system operation requires a clear view of the road by the camera. Have any windshield damage in the area of the camera's field of view repaired.
Note:
If something hits the front end of your vehicle or damage occurs, the radar sensing zone may change. This could cause missed or false vehicle detections. Contact an authorized dealer to have the radar checked for proper coverage and operation.
Note:
If your vehicle detects excessive heat at the camera or a potential misalignment condition, a message may display in the information display indicating temporary sensor unavailability. This message deactivates automatically when operational conditions are correct. For example, when the ambient temperature around the sensor decreases or the sensor automatically recalibrates.