WARNING:
Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle. We recommend against the use of any hand-held device while driving and encourage the use of voice-operated systems when possible. Make sure you are aware of all applicable local laws that may affect the use of electronic devices while driving. |
You can control various systems on your vehicle using the information display control by the speedometer. The corresponding information is appears in the information display.
Base Information Display Control

Press and release the SELECT/RESET stem, by the speedometer, to choose settings and confirm messages. Select or reset the function by holding the SELECT/RESET stem for more than two seconds.
| Info
|
|---|
| TRIP A or B
|
| ALOC
| On or Off
|
| AUnLOC
| On or Off
|
TRIP A or B
Registers the distance of individual journeys.
Optional Information Display Control

Press and release the SELECT/RESET stem, by the speedometer, to choose settings and confirm messages. Select or reset the function by holding the SELECT/RESET stem for more than two seconds.
| Info
|
|---|
| TRIP A or B
|
| Miles (km) to E
|
| XX.X AVG MPG (L/100km)
|
| MPG (L/km)
|
| HOLD RESET FOR SETUP MENU
|
| HOLD RESET FOR SYSTEM CHECK
|
TRIP A or B
Registers the distance of individual journeys.
Miles (km) to E
This displays an estimate of approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to switch the ignition off when refueling to allow this feature to detect the added fuel correctly. Based on your recent driving history of
500 mi (800 km), the system calculates the distance to empty using a running average fuel economy. This value is not the same as the average fuel economy display. The running average fuel economy re-initializes to a factory default value if the battery is disconnected.
XX.X AVG MPG (L/100km)
Average fuel economy displays your average fuel economy in miles/gallon or liters/100 km.
MPG (L/km)
This displays instantaneous fuel economy as a bar graph. Your vehicle must be moving to calculate instantaneous fuel economy. You cannot reset instantaneous fuel economy.
System check and vehicle feature customization (If Equipped)
Note:
System check and vehicle feature customization is only available with the optional information display controls.
Note:
When returning to the setup menu and you select a non-English language, you will see a message appear HOLD RESET FOR ENGLISH to change back to English. Press and hold the SELECT/RESET stem to change back to English.

Press and hold the SELECT/RESET stem to get into the setup menu sequence for the following displays:
| Setup
|
|---|
| OIL LIFE
|
| UNITS ENG / METRIC
| Press and hold the SELECT/RESET stem
| English or Metric
|
| AUTOLOCK (if equipped)
| ON or OFF
|
| AUTOUNLOCK (if equipped)
| ON or OFF
|
| COMPASS ZONE (if equipped)
|
| TBC MODE (if equipped)
| Press and hold the SELECT/RESET stem
| Electric or EOH
|
| LANGUAGE = ENGLISH / SPANISH / FRENCH
| English / Spanish / French
|
| SYSTEM CHECK
|
|---|
| RESET FOR SYSTEM CHECK
| Press and hold the SELECT/RESET stem
| XXX% OIL LIFE
|
| ENGINE HOURS (if enabled)
|
| ENGINE IDLE HOURS (if enabled)
|
| CHARGING SYSTEM
|
| BRAKE SYSTEM
|
| TBC GAIN = XX.X or NO TRAILER (if equipped)
|
| TBC GAIN = XX.X or OUTPUT = ////// (if equipped)
|
| XXX MILES TO E
|
OIL LIFE XXX% HOLD RESET = NEW
This displays the remaining oil life. An oil change is required whenever indicated by the message center and according to the recommended maintenance schedule. USE ONLY RECOMMENDED ENGINE OILS.
To reset the oil monitoring system to 100% after each oil change, perform the following:
- Press and release the SELECT/RESET stem to display OIL LIFE XXX% HOLD RESET = NEW.
- Press and hold the SELECT/RESET stem for two seconds and release to reset the oil life to 100%.
Note:
To change oil life 100% value (if equipped):
- Once OIL LIFE SET TO XXX% displays, release and press the SELECT/RESET stem to change the oil life start value. Each release and press reduces the value by 10%.
UNITS ENG / METRIC
Displays the current units in English or Metric.
AUTOLOCK
This feature automatically locks all vehicle doors when you shift into any gear, putting the vehicle in motion.
AUTOUNLOCK
This feature automatically unlocks all vehicle doors when you open the driver's door within 10 minutes of switching the ignition off.
COMPASS
Displays the vehicle's heading direction.
Note:
Driving near large buildings, bridges, power lines and powerful broadcast antennas may affect the compass reading. Magnetic or metallic objects placed in, on or near the vehicle may also affect compass accuracy. If the compass appears to be inaccurate, a manual calibration may be necessary. Refer to Compass zone adjustment.
Compass zone adjustment

- Determine which magnetic zone you are in for your geographic location by referring to the zone map.
- Press and release the SELECT/RESET stem to scroll through the information displays until the message center displays HOLD RESET FOR SETUP MENU.
- Press and hold the SELECT/RESET stem to get into the setup menu. Press repeatedly to scroll through the setup menu until COMPASS ZONE XX appears in the information display.
- Press and hold the SELECT/RESET stem for approximately two seconds to go to the next zone, then release.
- Press and hold to go up by one zone then release. Repeat this until you reach the desired zone.
- To exit the procedure, release the SELECT/RESET stem and allow the setup timer to expire.
Compass calibration adjustment
Note:
For optimum calibration, drive to an open, level location away from large metallic objects or structures. Switch off all non-essential electrical accessories (heated rear window, heater, A/C, map lamps, wiper) and make sure all the doors are closed.
Note:
If you press the SELECT/RESET stem during the calibration or three minutes elapse since the beginning of the calibration without driving the vehicle, the information display reverts back to normal operation and CAL displays until you complete a successful calibration.
- Press and release the SELECT/RESET stem to scroll through the information displays until HOLD RESET FOR SETUP MENU appears.
- Press and hold the SELECT/RESET stem to get into the setup menu. Press it repeatedly to scroll through the setup menu until HOLD RESET FOR CALIBRATION appears in the information display.
- Press and hold the SELECT/RESET stem for approximately two seconds until the information display enters the compass zone adjustment mode.
- Press and hold the SELECT/RESET stem until CIRCLE SLOWLY TO CALIBRATE appears in the information display.
- Slowly drive the vehicle in a circle less than
3 mph (5 km/h) until the CIRCLE SLOWLY TO CALIBRATE message changes to CALIBRATION COMPLETED. This may require up to five circles to complete the calibration.
TBC MODE
Allows you to choose the trailer brake mode.
LANGUAGE = ENGLISH / SPANISH / FRENCH
Allows you to choose which language appears in the information display.
Waiting four seconds or pressing the SELECT/RESET stem cycles the information display through each of the language choices.
Press the SELECT/RESET stem to set the language choice when the language you want appears.
HOLD RESET FOR SYSTEM CHECK
The information display begins to cycle through the vehicle systems and provides a status of the item if needed. Some systems show a message only if a condition is present.