This view of the Owner's Manual contains the very latest information, which may vary slightly from the printed Owner's Manual originally provided with your vehicle. It may also describe content that is not on or operates differently on your vehicle. Please consider the Owner's Manual originally provided with your vehicle as the primary source of information for your vehicle.
The information contained in this publication was correct at the time of release.In the interest of continuous development, we reserve the right to change specifications, design or equipment at any time without notice or obligation.No part of this publication may be reproduced, transmitted, stored in a retrieval system or translated into any language in any form by any means without our written permission.Errors and omissions excepted.
Copyright © 2024 Ford Motor Company
Passive Anti-Theft System
Note:
The system is not compatible with non-Ford aftermarket remote start systems.Use of these systems may result in engine starting problems and a loss of security protection.
Note:
Metallic objects, electronic devices or a second coded key on the same key chain may result in vehicle starting problems, especially if they are too close to the key when starting your vehicle.Prevent these objects from touching the coded key when starting your vehicle.Switch the ignition off, move all objects on the key chain away from the coded key and restart your vehicle if a problem occurs.
Note:
Do not leave a duplicate coded key in your vehicle.Always take your keys and lock all doors when leaving your vehicle.
SecuriLock™
The system helps prevent the engine from starting unless you use a coded key programmed to your vehicle. Using the wrong key may prevent your vehicle from starting. A message may appear in the information display.
If you are unable to start your vehicle with a coded key, it is not operating correctly. A message may appear in the information display.
Automatic Arming
The system arms when you switch the ignition off.
Automatic Disarming
The system disarms when you switch the ignition on with a coded key.
Replacement Keys
Note:
Your vehicle comes with two keys.
The intelligent access key functions as a programmed key that operates the driver door lock and turns on the intelligent access with push button start system, as well as a remote control.
If your coded keys are lost or stolen and you do not have an extra coded key, you need to erase the key codes from your vehicle and program new coded keys. Contact an authorized dealer.
Store a spare intelligent access key away from your vehicle in a safe place. You can purchase replacement keys or remote controls from an authorized dealer.
Programming a Spare Intelligent Access Key
Note:
You can program a maximum of four intelligent access keys to your vehicle.
You must have two previously programmed intelligent access keys inside your vehicle and the new unprogrammed intelligent access keys readily accessible. Contact an authorized dealer to have the spare key programmed if two previously programmed keys are not available.
Make sure that the ignition is switched off before beginning this procedure. Make sure that you close all the doors before beginning and that they remain closed throughout the procedure. Carry out all steps within 30 seconds of starting the sequence. Stop and wait for at least one minute before starting again if you carry out any steps out of sequence.
Read and understand the entire procedure before you begin.
- Open the floor console storage compartment lid.
- With the buttons facing up and the unlock button facing the front of your vehicle, place the first intelligent access key onto the back up slot inside the center console.
- Press the push button ignition switch.
- Wait five seconds and then press the push button ignition switch again.
- Remove the intelligent access key.
- Within 10 seconds, place a second programmed intelligent access key onto the backup slot and press the push button ignition switch.
- Wait five seconds and then press the push button ignition switch again.
- Remove the intelligent access key.
- Wait five seconds, then place the unprogrammed intelligent access key onto the backup slot and press the push button ignition switch.
- Once complete, the information cluster displays a message confirming that you have programed the key.
If programming was unsuccessful, wait 10 seconds and repeat the procedure. If it still does not work, take your vehicle to an authorized dealer.
- Please note that Ford will not respond to individual feedback.
- Please provide detailed feedback regarding any inaccuracies in the content or any missing content in the Owner's Manual.
- Your feedback will be investigated, and any necessary changes will be updated in the online Owner's Manual.
Your input is valuable in helping us improve our Owner's Manual. Thank you for taking the time to provide your feedback.