Integrated Keyhead Transmitter (If Equipped)
Integrated Keyhead Transmitter
Use the key blade to start your vehicle and unlock or lock the driver door from outside your vehicle. You can also use the key blade to lock and unlock the glove compartment.The transmitter portion functions as the remote control.
Intelligent Key Transmitter Tag
Note:   Your vehicle keys came with a security label that provides important key cut information.Keep the label in a safe place for future reference.
Intelligent Access Key (If Equipped)
Note:   A three-button remote control operates similarly.
Ignition Key/Remote Control
 The intelligent access keys operate the power locks and the remote start system. The key must be in your vehicle to use the push button start.
Intelligent Access Key Blade Release
 The intelligent access key also contains a removable key blade that you can use to unlock your vehicle. You can also use the key blade to lock and unlock the glove compartment.Slide the release on the back of the remote control to release the key blade, then pull the blade out.
Intelligent Access Key Security Label
Note:   Your vehicle keys came with a security label that provides important key cut information.Keep the label in a safe place for future reference.
Replacing the Battery
Note:   Refer to local regulations when disposing of transmitter batteries.
Note:   Do not wipe off any grease on the battery terminals or on the back surface of the circuit board.
Note:   Replacing the battery does not erase the programmed key from your vehicle.The transmitter should operate normally.
The remote control uses one coin-type three-volt lithium battery CR2032 or equivalent.
Integrated Keyhead Transmitter
Integrated Keyhead Transmitter
  1. Twist a thin coin in the slot of the transmitter near the key ring to remove the battery cover.
  1. Carefully remove the rubber gasket from the transmitter if it does not come off with the battery cover.
  1. Remove the old battery.
Integrated Key
  1. Insert a new battery with the + facing upward. Press the battery down to make sure it is fully in the housing.
  1. Reinstall the battery housing cover onto the transmitter.
Intelligent Access Key
  1. Remove the key blade from the transmitter.
Remove the Remote Control Battery Cover
  1. Twist a thin coin under the tab hidden behind the key blade head to remove the battery cover. Do not use the key blade to remove the cover or you could damage it.
Changing the Remote Key Battery
  1. Remove the old battery.
  1. Insert a new battery with the + facing downward. Press the battery down to make sure it is fully in the housing.
  1. Reinstall the battery housing cover onto the transmitter and install the key blade.
Car Finder
Lock Icon  Press the button twice within three seconds.
 The horn sounds and the direction indicators flash. We recommend you use this method to locate your vehicle, rather than using the panic alarm.
Note:   If any door or the liftgate is open, or if the hood is open on vehicles with an anti-theft alarm or remote start, the horn will sound twice and the direction indicators will not flash.
Sounding the Panic Alarm
Volume Icon   Press the button to sound the panic alarm. Press the button again or switch the ignition on to turn it off.
Note:   The panic alarm only operates when the ignition is off.
Remote Start (If Equipped)
WARNING   WARNING:  To avoid exhaust fumes, do not use remote start if your vehicle is parked indoors or in areas that are not well ventilated.

Note:   Do not use remote start if your fuel level is low.
Remote Start Button  The remote start button is on the transmitter.
 This feature allows you to start your vehicle from the outside.The transmitter has an extended operating range.
Vehicles with automatic climate control can be configured to operate when the vehicle is remote started.   See   Automatic Climate Control - Vehicles With: Premium AM/FM/CD. 
Many states and provinces have restrictions for the use of remote start.Check your local and state or provincial laws for specific requirements regarding remote start systems.
The remote start system does not work if any of the following occur:
  • The ignition is on.
  • The anti-theft alarm triggers.
  • You switch off the feature.
  • The hood is open.
  • The transmission is not in park (P).
  • The battery voltage is below the minimum operating voltage.
  • The service engine soon indicator was on the last time your vehicle was driven.
Remote Starting Your Vehicle
Note:   You must press each button within three seconds of each other.If you do not follow this sequence, your vehicle does not start remotely, the direction indicators do not flash twice and the horn does not sound.
Remote Starting Your Vehicle
To start your vehicle remotely:
  1. Press the lock button to lock all the doors.
  1. Press the remote start button twice.The exterior lamps flash twice.
The horn sounds if the system fails to start, unless quiet start is on. Quiet start runs the blower fan at a slower speed to reduce noise. You can switch this feature on or off in the information display.   See   General Information. 
Note:   If you remote start your vehicle with an integrated keyhead transmitter, you must switch the ignition on before driving your vehicle.If you remote start your vehicle with an intelligent access transmitter, you must press the push button ignition switch on the instrument panel once while applying the brake pedal before driving your vehicle.
The power windows do not work during remote start and the radio does not turn on automatically.
The parking lamps remain on and the vehicle runs for 5, 10 or 15 minutes, depending on the setting.
Extending the Engine Running Time
 To extend the engine running time duration of your vehicle during remote start, repeat steps 1 and 2 while the engine is running. If the duration is set to 10 minutes, the duration extends by another 10 minutes.For example, if your vehicle had been running from the first remote start for 5 minutes, your vehicle continues to run now for a total of 20 minutes. You can extend the remote start up to a maximum of 35 minutes.
Wait at least five seconds before remote starting after the engine stops running.
Turning Your Vehicle Off After Remote Starting
Remote Start Button   Press the button once. The parking lamps turn off.
You may have to be closer to your vehicle to remotely switch off your vehicle after remote starting. This is due to the added noise of your running vehicle.
You can switch this feature on or off in the information display.   See   General Information. 
Memory Feature (If Equipped)
You can use the remote control to recall memory settings for the driver seat, power mirrors, power steering column and power adjustable foot pedals. Press the unlock button on the remote control or unlock your vehicle with the intelligent access key to recall the memory positions. You can program the remote control or intelligent access key to recall memory positions.   See   Memory Function. 

Owner's Manual Feedback

Submit

Thank You For Your Feedback

Ok