This view of the Owner's Manual contains the very latest information, which may vary slightly from the printed Owner's Manual originally provided with your vehicle. It may also describe content that is not on or operates differently on your vehicle. Please consider the Owner's Manual originally provided with your vehicle as the primary source of information for your vehicle.
The information contained in this publication was correct at the time of release.In the interest of continuous development, we reserve the right to change specifications, design or equipment at any time without notice or obligation.No part of this publication may be reproduced, transmitted, stored in a retrieval system or translated into any language in any form by any means without our written permission.Errors and omissions excepted.
Copyright © 2024 Ford Motor Company
Keyless Entry
You can use the keypad to do the following:
SECURICODE™ Keyless Entry Keypad
The keypad is near the driver window. It illuminates when touched.
Note:
If you enter your entry code too fast on the keypad, the unlock function may not work.Enter your entry code again more slowly.
You can use the keypad to do the following:- Lock or unlock the doors.
- Program and erase user codes.
- Arm and disarm the anti-theft alarm.
You can operate the keypad with the factory-set five-digit entry code.The code is on the owner's manual wallet card in the glove box and is available from an authorized dealer. You can also program up to five of your own five-digit personal entry codes.
Programming a Personal Entry Code
- Enter the factory-set five-digit code.
- Press 1·2 on the keypad within five seconds.
- Enter your personal five-digit code.You must do this within five seconds of completing step 2.
- Press 1·2 on the keypad to save personal code 1.
The doors lock then unlock to confirm that programming was successful.
To program additional personal entry codes, repeat steps 1 through 3, then for step 4:- Press 3·4 to save personal code 2.
- Press 5·6 to save personal code 3.
- Press 7·8 to save personal code 4.
- Press 9·0 to save personal code 5.
For vehicles with SYNC 3, you can also program the system with a personal entry code. See
Settings.
Hints:- Do not set a code that uses five of the same number.
- Do not use five numbers in sequential order.
- The factory-set code works even if you have set your own personal code.
Erasing a Personal Code
- Enter the factory-set five-digit code.
- Press and release 1·2 on the keypad within five seconds.
- Press and hold 1·2 for two seconds. You must do this within five seconds of completing Step 2.
All personal codes erase and only the factory-set five-digit code works.
Anti-Scan Feature
The keypad goes into an anti-scan mode if you enter the wrong code seven times. This mode turns off the keypad for one minute and the keypad lamp flashes.
The anti-scan feature turns off after:- One minute of keypad inactivity.
- You press the unlock button on the remote control.
- You switch the ignition on.
- You unlock your vehicle using intelligent access.
Locking and Unlocking the Doors
Locking All Doors
Press and hold 7·8 and 9·0 simultaneously with the driver door closed. You do not need to enter the keypad code first.
Unlocking the Driver Door
Enter the factory-set or your personal five-digit code. You must press each number within five seconds of each other. The interior lamps illuminate.
Note:
All doors unlock if you switch on the all-door unlocking mode. See
Locking and Unlocking.
Unlocking All Doors
Enter the factory-set or your personal five-digit code, then press 3·4 within five seconds.
Displaying the Factory-Set Code
Note:
You need to have two programmed intelligent access keys for this procedure.
- Open the floor console storage compartment lid.
- With the buttons facing up and the unlock button facing the front of your vehicle, place the first intelligent access key onto the back up slot inside the center console.
- Press the push button ignition switch once and wait a few seconds.
- Press the push button ignition switch again and remove the key.
- Place the second programmed key onto the backup slot, then press the push button ignition switch.
The factory-set code appears in the information display for a few seconds.
Note:
The code may not display until after any other warning messages first display.