Intelligent Access Key
Note:
You may not be able to shift out of park (P) unless the remote control is inside your vehicle.
The remote control operates the power locks and the remote start system.The key must be in your vehicle to activate the push-button start system.
Removable Key Blade
The remote control also contains a removable mechanical key blade that you can use to unlock the driver door.
Push the release button and pull the key blade out.
Note:
Your vehicle keys came with a security label that provides important key cut information.Keep the label in a safe place for future reference.
Replacing the Battery
WARNING:
Keep batteries away from children to prevent ingestion. Failure to follow this instruction could result in personal injury or death. If ingested, immediately seek medical attention.
WARNING:
If the battery compartment does not securely close, stop using the remote control and replace it as soon as possible. In the meantime, keep the remote control away from children. Failure to follow this instruction could result in personal injury or death. |
Note:
Refer to local regulations when disposing of remote control batteries.
Note:
Do not wipe off any grease on the battery terminals or on the back surface of the circuit board.
Note:
Replacing the battery does not delete the remote control programming to your vehicle. The remote control should operate normally after you replace the battery.
A message appears in the information display when the remote control battery is low. See
Information Displays.
Intelligent Access Key
The remote control uses one coin-type three-volt lithium battery CR2450 or equivalent.
- Push the release button and pull the key blade out.
- Twist a thin coin under the tab hidden behind the key blade head to remove the battery cover.
- Insert a suitable tool, for example a screwdriver, in the position shown and carefully remove the battery.
- Install new battery with the + facing upward.
- Reinstall the battery cover and the key blade.
Using the Key Blade
The key cylinder is under a cap on the driver door handle.
To remove the cap:
- Insert the key blade into the slot on the bottom of the handle and press up.
- While maintaining upward pressure, move the cap rearward to release it. Gently remove the key while doing so.
To install the cap:
- Place the cap just forward of the key cylinder.
- While applying pressure to the cap, move it forward until it is in place. You may hear a snap as it engages.
Make sure you have properly installed the cap by trying to move it rearward.
Linking a Preset Position to Your Remote Control
Locating Your Vehicle
Press the button twice within three seconds. The horn sounds and the direction indicators flash. We recommend you use this method to locate your vehicle, rather than using the panic alarm. | |
Sounding a Panic Alarm
Note:
The panic alarm only operates when the ignition is off.
Press the button to sound the panic alarm.Press the button again or switch the ignition on to deactivate. | |
Remote Start (If Equipped)
WARNING:
To avoid exhaust fumes, do not use remote start if your vehicle is parked indoors or in areas that are not well ventilated. |
Note:
Do not use remote start if your fuel level is low.
The remote start button is on the remote control.
This feature allows you to start your vehicle from outside the vehicle.The remote control has an extended operating range.
Vehicles with automatic climate control can be configured to operate when the vehicle is remote started. See
Climate Control.
Many states and provinces have restrictions for the use of remote start.Check your local and state or provincial laws for specific requirements regarding remote start systems.
The remote start system does not work if:
- The ignition is on.
- The alarm system is triggered.
- You switch off the feature in the information display. See
Information Displays.
- The hood is open.
- The transmission is not in park (P).
- The vehicle battery voltage is too low.
- The service engine soon light is on.
Remote Starting Your Vehicle
Note:
You must press each button within three seconds of each other.If you do not follow this sequence, your vehicle does not start remotely, the direction indicators do not flash twice and the horn does not sound.
To remote start your vehicle:
- Press the lock button.
- Press the remote start button twice.The exterior lamps flash twice.
The horn sounds if the system fails to start.
The power windows do not work during the remote start and the radio does not turn on automatically.
The parking lamps remain on and the vehicle will run for 5, 10, or 15 minutes, depending on the setting. See
Information Displays.
Extending the Vehicle Run Time
To extend the engine running time duration of your vehicle during remote start, repeat steps 1 and 2 while the engine is running.If you programmed the duration to last 10 minutes, the second 10 minutes will begin after what is left of the first activation time.For example, if your vehicle had been running from the first remote start for 5 minutes, your vehicle continues to run now for a total of 20 minutes. You can extend the remote start up to a maximum of 35 minutes.
Wait at least five seconds before remote starting after a vehicle shutdown.
Turning Your Vehicle Off After Remote Starting
Press the button once. The parking lamps turn off. You may have to be closer to your vehicle to remotely switch off your vehicle after remote starting. This is due to the added noise of your running vehicle. You can disable or enable the remote start system through the information display. See
Information Displays.
| |
Remote Control Feedback
An LED on the remote control provides status feedback of remote start or stop commands.
LED
| Status
|
---|
Solid green
| Remote start or extension successful
|
Solid red
| Remote stop successful; engine off
|
Blinking red
| Remote start or stop failed
|
Blinking green
| Waiting for status update from vehicle
|
Global Opening and Closing
You can use the remote control to operate the windows.
Memory Feature (If Equipped)
You can use the remote control to recall memory positions.If programmed to a pre-set position, the remote control recalls memory positions when you unlock your vehicle. See
Memory Function.
Remote Control Information Messages
Message
| Action
|
---|
Key Battery Low Replace Soon | Displays when the remote control battery requires replacing.
|