This view of the Owner's Manual contains the very latest information, which may vary slightly from the printed Owner's Manual originally provided with your vehicle. It may also describe content that is not on or operates differently on your vehicle. Please consider the Owner's Manual originally provided with your vehicle as the primary source of information for your vehicle.
The information contained in this publication was correct at the time of release.In the interest of continuous development, we reserve the right to change specifications, design or equipment at any time without notice or obligation.No part of this publication may be reproduced, transmitted, stored in a retrieval system or translated into any language in any form by any means without our written permission.Errors and omissions excepted.
Copyright © 2024 Ford Motor Company
Keyless Entry
You can use the keypad to:
SECURICODE™ KEYLESS ENTRY KEYPAD
The keypad is near the driver window. It illuminates when touched.
Note:
If you enter your entry code too fast on the keypad, the unlock function may not work.Enter your entry code again more slowly.
You can use the keypad to:- Lock or unlock the doors.
- Program and erase user codes.
- Arm and disarm the anti-theft alarm.
Note:
You must have an intelligent access key within
3 ft (1 m) of your vehicle.
You can operate the keypad with the factory-set five-digit entry code. The code is on the owner's wallet card in the glove box and is available from an authorized dealer. You can also program up to five of your own five-digit personal entry codes.
Programming a Personal Entry Code
To create your own personal entry code:
- Enter the factory-set five-digit code.
- Press 1·2 on the keypad within five seconds.
- Enter your personal five-digit code.You must press each number within five seconds of each other.
- Press 1·2 on the keypad to save personal code 1.
The doors lock then unlock to confirm that programming was successful.
To program additional personal entry codes, repeat Steps 1-3, then for Step 4:
- Press 3·4 to save personal code 2
- Press 5·6 to save personal code 3
- Press 7·8 to save personal code 4
- Press 9·0 to save personal code 5.
You may also program a personal entry code through the information display.
Tips:- Do not set a code that uses five of the same number.
- Do not use five numbers in sequential order.
- The factory-set code works even if you have set your own personal code.
Erasing a Personal Code
- Enter the factory-set 5-digit code.
- Press and release 1·2 on the keypad within five seconds.
- Press and hold 1·2 for two seconds. You must do this within five seconds of completing Step 2.
All personal codes erase and only the factory-set 5-digit code works.
Anti-Scan Feature
The keypad goes into an anti-scan mode if you enter the wrong code seven times (35 consecutive button presses). This mode disables the keypad for one minute and the keypad lamp flashes.
The anti-scan feature turns off after:- One minute of keypad inactivity.
- Pressing the unlock button on the remote control.
- Switching the ignition on.
Displaying the Factory Set Code
Note:
You need to have two programmed keys for this procedure.
To display the factory-set code in the information display:
- Insert a key into the ignition and switch the ignition on for a few seconds.
- Switch the ignition off and remove the key.
- Insert the second key into the ignition and switch the ignition on.
The factory-set code will display for a few seconds.
Note:
The code may not display until after any other warning messages first display.
Locking and Unlocking
To Unlock the Driver Door
Enter the factory-set 5-digit code or your personal code.You must press each number within five seconds of each other. The interior lamps illuminate.
Note:
All doors unlock if you disable the two-stage unlocking mode. See
Locking and Unlocking.
To Unlock All Doors
Enter the factory-set code or your personal code, then press 3·4 within five seconds.
To Lock All Doors
Press and hold 7·8 and 9·0 at the same time (with the driver door closed). You do not need to enter the keypad code first.
Displaying the Factory-Set Code
Note:
Do not place the device on the wireless accessory charging area when programming intelligent access keys.
Note:
You can program a maximum of four keys to your vehicle.
Read and understand all of the steps that follow before you begin.
You must have two previously programmed intelligent access keys inside your vehicle and the new unprogrammed intelligent access key readily accessible. You can purchase replacement keys or remote controls from an authorized dealer.
Make sure that you switch off the ignition before beginning this procedure. Make sure that you close all the doors before beginning and that they remain closed throughout the procedure. Carry out all steps within 30 seconds of starting the sequence. Stop and wait for at least one minute before starting again if you carry out any steps out of sequence.
- Access the backup slot.
- With the buttons facing the rear of your vehicle and the key ring facing upward, place the first intelligent access key into the backup slot inside the center console.
- Press the push button ignition switch once and wait for a few seconds.
- Press the push button ignition switch again and remove the intelligent access key from the center console.
- Insert the second programmed key into the backup slot in the center console, then press the push button ignition switch.
The factory-set code appears in the information display for a few seconds.
Note:
The code may not display until after any other warning messages first display.
- Please note that Ford will not respond to individual feedback.
- Please provide detailed feedback regarding any inaccuracies in the content or any missing content in the Owner's Manual.
- Your feedback will be investigated, and any necessary changes will be updated in the online Owner's Manual.
Your input is valuable in helping us improve our Owner's Manual. Thank you for taking the time to provide your feedback.