WARNING   WARNING:  Do not leave children or pets unattended in your vehicle. Failure to follow this instruction could result in personal injury or death.
WARNING   WARNING:  When closing the power windows, verify they are free of obstruction and make sure that children and pets are not in the proximity of the window openings.

Note:   If you operate the switches often during a short period of time the system might become inoperable for a certain time to prevent damage due to overheating.
Note:   If you operate both the switch on the relevant door and the switch for that window on the driver’s door at the same time, the window stops moving.
Note:   You may hear a pulsing noise when you open just one of the windows. Lower the opposite window slightly to reduce this noise.
Driver Door Switches (Single Cab)
Driver Door Switch
APress the switch to open the window.
BLift the switch to close the window.
Driver Door Switches (Double Cab)
Driver Door Switch
APress the switch to open the window.
BLift the switch to close the window.
Front and Rear Passenger Door Switches
Passenger Power Window Switch
APress the switch to open the window.
BLift the switch to close the window.
Opening and Closing the Driver Side Window Automatically
Press or lift the switch to the second action point and release it.
Press again or lift it to stop the window.
Opening and Closing Other Windows Automatically (If Equipped)
Press or lift the switch to the second action point and release it.
Press again or lift it to stop the window.
Safety Switch for the Rear Windows
Note:   Once you press the safety switch, you can still operate the rear windows and front passenger window from the driver door if you have global opening and closing.
Note:   In vehicles without global opening and closing, you cannot operate the rear windows from driver side when you press the safety switch.In certain vehicles, you cannot operate front passenger windows as well.
Rear Window Control - Lock/Unlock
Press the control to lock or unlock the rear window controls.
Resetting the Memory of the Electric Windows - Vehicle with One Touch Up/Down on Driver Side only
Note:   The bounce back feature remains turned off until you reset the memory.
In the event of a flat battery or after the battery is disconnected from the vehicle, you must reset the memory for the driver window.
  1. Open the window and then try to close it using the one-touch feature.
  1. Lift and hold the switch to the second action point until you fully close the window.
  1. Lift and hold the switch for more than two seconds and release.
  1. Open the window using the first action point and try to close it automatically using the second action point.
  1. If the window does not open or close automatically when you press the switch or lift it to the second action point, repeat the procedure.
Safety Mode
Note:   The anti-trap function is not active during this procedure.
If the system detects a malfunction, it enters a safety mode. The windows move a little at a time and then stop again. Close the windows by pressing the switch again when the windows stop moving.
Contact an authorized dealer.
Bounce-Back
The window automatically stops and reverses some distance if it detects an obstacle when closing.
Overriding the Bounce-Back Feature
WARNING   WARNING:  If you override bounce-back, the window does not reverse if it detects an obstacle. Take care when closing the windows to avoid personal injury or damage to your vehicle.

Proceed as follows to override this protection feature when there is a resistance, for example in winter:
  1. Close the window twice until it reaches the point of resistance and let it reverse.
  1. Close the window a third time to the point of resistance. The bounce-back feature is now disabled and you can close the window manually. The window will go past the point of resistance and you can close it fully.
See an authorized dealer as soon as possible if the window does not close after the third attempt.
Resetting the Bounce-Back Feature
Note:   The bounce-back feature remains turned off until you reset the memory.
If you disconnect the battery, you must reset the bounce-back memory separately for each window.
  1. Lift and hold the switch until you fully close the window.
  1. Release the switch.
  1. Lift the switch again for one second.
  1. Press and hold the switch until you fully close the window.
  1. Release the switch.
  1. Lift and hold the switch until you fully close the window.
  1. Open the window and then try to close it automatically.
  1. Reset and repeat the procedure if the window does not close automatically.

Owner's Manual Feedback

  • Please note that Ford will not respond to individual feedback.
  • Please provide detailed feedback regarding any inaccuracies in the content or any missing content in the Owner's Manual.
  • Your feedback will be investigated, and any necessary changes will be updated in the online Owner's Manual. 

Submit

Your input is valuable in helping us improve our Owner's Manual. Thank you for taking the time to provide your feedback.

Ok